Wolo 140-24 Sea Alert Instrukcja Użytkownika Pobierz pdf

Your purchase of a Wolo SEA ALERT™ Air Horn will complement your boat, while offering an extra level of

protection. Wolo’s products are manufactured with the ﬁnest materials. Before being packaged, each horn

is tested to ensure it meets all of our manufacturing speciﬁcations. If you need help installing your new Wolo

horn, our technicians are available to answer your questions, Monday thru Friday, 9 AM to 4 PM EST at

1-888-550-HORN (4676).

Before installation of the horn is attempted, it is important to read these instructions completely. The lives of

people can be dependent on a proper installation of the horn. The person doing the installation must have

knowledge of the proper method for mounting and securing the horn to the exterior of the boat, as well as

knowledge of the boat’s electrical system. Again, read the instructions completely and note any messages

marked “IMPORTANT” or “WARNING’’. A safe installation will prevent injury or damage to the boat.

WARNING: Installation of the SEA ALERT requires drilling. The installer must carefully inspect both sides of

the selected mounting locations to ensure that there are no wires, fuel lines and or any other components that

could be damaged by drilling.

WARNING: If any wires are routed through drilled holes, always de-burr ensuring that there are no sharp

edges. Install a rubber grommet into all metal holes that wires are being routed through.

MOUNTING TRUMPET: Fig. 1 & 2

IMPORTANT: The horn should be mounted facing forward

whenever possible. The NMMA Certiﬁcation Program

requires this for boats 39’ or longer.

1. Locate the desired mounting location of the trumpet.

For best results, the front of the horn should be

unobstructed so that the sound can carry straight ahead.

IMPORTANT: FOR BEST PERFORMANCE AND SOUND,

ALWAYS MOUNT THE COMPRESSOR CLOSE TO

TRUMPET, KEEPING THE HOSE LENGTH AS SHORT AS

POSSIBLE. THE COMPRESSOR MUST BE MOUNTED IN

A DRY INTERIOR LOCATION).

2. Use the horn’s gasket as a template, mark hole locations

and drill to size.

3. Thread the chrome air inlet tube into the base of the horn.

4. Mount and secure the horn as shown in Fig. 1.

IMPORTANT: Be sure to use the provided rubber

gasket to protect against water leaks. Tighten the base

plate front screw and rear nut that threads onto the air

inlet tube evenly to ensure a watertight seal.

5. Position the front trumpet support bracket around the

narrow part of the trumpet. IMPORTANT: Provided in the

kit is a soft rubber strip that is placed into the ring of the

support bracket to provide a tight ﬁt and prevent vibration.

Push the bracket forward until it is tight. Use the bracket as

a template, mark hole locations and drill to size. See Fig 2.

6. Secure the front trumpet support bracket using the hardware provided. Tighten screws evenly to

ensure a watertight seal. IMPORTANT: Be sure to use the rubber gasket provided to protect against

water leaks.

INSTALLATION INSTRUCTIONS

Model 140-24 & 145-24 SEA ALERT

™

24-Volt

air inlet

tube

1 2 3 4

INSTALLATION INSTRUCTIONS 1
WARRANTY 4

Podsumowanie treści

Strona 1 - INSTALLATION INSTRUCTIONS

Your purchase of a Wolo SEA ALERT™ Air Horn will complement your boat, while offering an extra level of protection. Wolo’s products are manufactured w

Strona 2

COMPRESSOR INSTALLATION: Fig. 3 & 4 7. Install the compressor in a dry interior location. IMPORTANT: The compressor should not be mounted further

Strona 3

WIRING: USING BOATS FACTORY HORN SYSTEM (TWO WIRE SYSTEM) Fig. 6 WARNING: You are required to use the relay supplied with this horn kit to protect the

Strona 4 - WARRANTY

ANY EXPRESSED WARRANTY NOT PROVIDED HEREIN IS EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPO